USER?S GUIDE 2621
World TimeCountdown Timer
World Time shows the current time in 30 cities (27 timeYou can set the countdown timer within a range of
Current time in the zone Hours Minutes
of the selected city code zones) around the world.one minute to 24 hours. An alarm sounds when the
All of the operations in this section are performed in thecountdown reaches zero.
World Time Mode, which you enter by pressing C.You can also select auto-repeat, which automatically
restarts the countdown from the original value you set
To view the time in another city codewhenever zero is reached.
In the World Time Mode, press D to scroll through cityCountdown timer functions are available in the
codes (time zones) to the east or B to scroll to the west.Countdown Timer Mode, which you can enter using C.
For full information about city codes, see the ?City Code
Table?.
City code If the current time shown for a city is wrong, check yourSeconds
Timekeeping Mode time and Home City code settings
Current day of week and make the necessary changes.
in the zone of the To use the countdown timer
selected city code
Press D while in the Countdown Timer Mode to start the countdown timer.
To toggle a city code time between Standard Time and Daylight Saving TimeWhen the end of the countdown is reached and auto-repeat is turned off, the alarm
1.In the World Time Mode, use B and D to display thesounds for 10 seconds or until you stop it by pressing any button. The countdown
city code (time zone) whose Standard Time/Daylighttime is automatically reset to its starting value after the alarm stops.
Saving Time setting you want to change.When the end of the countdown is reached and auto-repeat is turned on, the alarm
2.Hold down A for about one second to toggle Daylightsounds, but the countdown starts again automatically whenever the countdown
Saving Time (DST displayed) and Standard Time (DSTreaches zero.
not displayed).The countdown timer measurement operation continues even if you exit the
The DST indicator is on the display whenever youCountdown Timer Mode.
display a city code for which Daylight Saving Time isPress D while a countdown operation is in progress to pause it. Press D again to
turned on.resume the countdown.
To completely stop a countdown operation, first pause it (by pressing D), and then
Note that the DST/Standard Time setting affects only the currently displayed citypress B. This returns the countdown time to its starting value.
code. Other city codes are not affected.
To set up the countdown timer
1.While the countdown start time is on the display in the
City TemperatureCountdown Timer Mode, hold down A until the hour
setting of the countdown start time starts to flash, which
In the City Temperature Mode, the display shows theAverage high indicates the setting screen.
temperature average high and low monthly temperatures in 30 citiesIf the countdown start time is not displayed, use the
around the globe.
Average low procedure ?To use the countdown timer? to display it.
temperature Note2.Press C to move the flashing in the sequence shown
Displayed temperatures are monthly averages. They dobelow to select other settings.
not ensure that the temperature on any particular date
will fall within the indicated range.HoursMinutesAuto-repeat
The average high temperature and low temperature
values alternate on the display at two-second intervals.3. While a setting is flashing, use D and B to change it as described below.
The screen that appears first is the one for the city and
month that was on the display when you last exited theScreenTo do this:Do this:
City Temperature Mode. 0:00Change the hours or minutesUse D (+) and B (-).
Month All of the operations in this section are performed in the
City code City Temperature Mode, which you enter by pressingOFFToggle auto-repeat on (ON) and off (OFF)Press D.
C.0:00
To specify a countdown start time of 24 hours, set .
To view city temperature data4. Press A to exit the setting screen.
1. In the City Temperature Mode, press D to scroll through city codes (time zones) toThe auto-repeat on indicator ( ) appears on the display while this function is turned on.
the east or B to scroll to the west.Frequent use of auto-repeat and the alarm can run down battery power.
2. Press A to display the data for the following month.
For full information about city code, see the ?City Code Table?.
Stopwatch
To specify the temperature unit
The stopwatch lets you measure elapsed time, split times,
While in the City Temperature Mode, press B and D at the same time to toggleMinutes Seconds and two finishes.
between Celsius ( C) and Fahrenheit ( F).The display range of the stopwatch is 59 minutes,
59.99 seconds.
The stopwatch continues to run, restarting from zero
Alarmafter it reaches its limit, until you stop it.
When the daily alarm is turned on, the alarm tone soundsThe stopwatch measurement operation continues even
Alarm timeif you exit the Stopwatch Mode.
(Hour : Minutes) when the alarm time is reached.Exiting the Stopwatch Mode while a split time is frozen
You can also turn on an Hourly Time Signal (:00) that
causes the watch to beep twice every hour on the hour.on the display clears the split time and returns to
Alarm setting (and Hourly Time Signal setting) iselapsed time measurement.
available in the Alarm Mode, which you enter byAll of the operations in this section are performed in the1/100 second
pressing C.Stopwatch Mode, which you enter by pressing C.
To measure times with the stopwatch
Elapsed Time
To set an alarm timeStartStopRe-startStopClear
1.In the Alarm Mode, hold down A until the hour setting
of the alarm time starts to flash, which indicates theSplit Time
setting screen.
This operation automatically turns on the alarm.StartSplitSplit releaseStopClear
2.Press C to move the flashing between the hour and( displayed)
minutes.
3.While a setting is flashing, use D (+) and B (-) toTwo Finishes
change it.
StartSplitStopSplit releaseClear
With the 12-hour format, set the time correctly as a.m. (A indicator) or p.m. (P indicator).First runner Second runner Display time of
4. Press A to exit the setting screen.finishes.finishes.second runner.
Display time of
Alarm Operationfirst runner.
The alarm tone sounds at the preset time for 20 seconds, regardless of the mode theThe time on the screen may not appear to stop immediately when you press a
watch is in.button to stop timing or to perform a split operation. Despite this, the time recorded
To stop the alarm tone after it starts to sound, press any button.by your button operation is accurate.
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn the Daily Alarm and Hourly Time Signal on and off
In the Alarm Mode, press B to cycle through the on and
off settings as shown below.
Alarm On Indicator/Hourly Time Signal On Indicator
Alarm OnAlarm OffAlarm OnAlarm Off
Signal OnSignal OffSignal OffSignal On
Alarm on Hourly Time
indicator Signal on
indicator The alarm on indicator flashes while the alarm is
sounding.
The alarm on indicator and Hourly Time Signal on
indicator are displayed in all modes.
2 |
ACEC
