MA0510-EA
Operation Guide 2996
About This Manual
" All of the displays in this manual show black on white.
" Button operations are indicated using the letters shown
in the illustration.
" Each section of this manual provides you with the
information you need to perform operations in each
mode. Further details and technical information can be
found in the OReference� section.
General Guide
" Press C to change from mode to mode.
" In any mode, press L to illuminate the display.
Timekeeping ModeWorld Time ModeStopwatch ModeCountdown Timer ModeAlarm Mode
Press .
TimekeepingWorld Time
Use the Timekeeping Mode to set and view the currentWorld Time shows the current time in 48 cities (29 time
Day of week time and date.City code zones) around the world.
Day " All of the operations in this section are performed in the
Read this before you set the time and date !World Time Mode, which you enter by pressing C.
The times displayed in the Timekeeping Mode and World
Time Mode are linked. Because of this, make sure youTo view the time for another city code
select a city code for your Home City (the city where youIn the World Time Mode, press D to scroll eastwardly
normally use the watch) before you set the time and date.through city codes or B to scroll westwardly.
" To view the current Home City code setting, press ACurrent time in the zone " For full information about city codes, see the OCity Code
while in the Timekeeping Mode.Table�.
PM indicator of the selected city code " If the current time shown for a city is wrong, check your
" For full information on city codes, see the OCity Code
Hour : Minutes Seconds Table�.Timekeeping Mode time and Home City code settings
and make the necessary changes.
To set the time and date
1.In the Timekeeping Mode, hold down A until theTo toggle a city code time between Standard Time and Daylight Saving Time
seconds start to flash, which indicates the setting1.In the World Time Mode, use D and B to display the
DST indicator
screen.city code (time zone) whose Standard Time/Daylight
2.Press C to move the flashing in the sequence shownSaving Time setting you want to change.
below to select other settings.2.Hold down A for about one second to toggle between
Daylight Saving Time (DST indicator displayed) and
Standard Time (DST indicator not displayed).
" The DST indicator is on the display whenever you
SecondsCity CodeDSTHourMinutesdisplay a city code for which Daylight Saving Time is
turned on.
" Note that the DST/Standard Time setting affects only the
currently displayed city code. Other city codes are not
DayMonthYear12/24-Hour Format
affected.
3. When the setting you want to change is flashing, use D and B to change it as" In the World Time Mode, you can switch the city code
described below.you currently have selected as your Timekeeping Mode
Home City between Standard Time and DST. The
ScreenTo do this:Do this:setting you select in the World Time Mode will also be
Reset the seconds to Press D.applied in the Timekeeping Mode.
Change the city codeUse D (east) and B (west).
Toggle between Daylight Saving Time ( )Press D.Stopwatch
and Standard Time ()
Change the hour or minutesUse D (+) and B (�).The stopwatch lets you measure elapsed time, split times,
1/100 second and two finishes.
Toggle between 12-hour () and 24-hourPress D." The display range of the stopwatch is 59 minutes,
() timekeeping59.99 seconds.
" The stopwatch continues to run, restarting from zero
Change the year, month, or dayUse D (+) and B (�).
after it reaches its limit, until you stop it.
" The stopwatch measurement operation continues even
" See ODaylight Saving Time (DST)� for details about the DST setting.if you exit the Stopwatch Mode.
4. Press A to exit the setting screen." Exiting the Stopwatch Mode while a split time is frozen
" Resetting the seconds to while the current count is in the range of 30 to 59Minutes Seconds on the display clears the split time and returns to
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds areelapsed time measurement.
reset to without changing the minutes." All of the operations in this section are performed in the
" With the 12-hour format, the P (PM) indicator appears on the display for times in theStopwatch Mode, which you enter by pressing C.
range of noon to 11:59 p.m. and no indicator appears for times in the range of
To measure times with the stopwatch
midnight to 11:59 a.m.
" With the 24-hour format, times are displayed in the range of 0:00 to 23:59, withoutElapsed Time
any indicator.
" The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode isStartStopRe-startStopClear
applied in all modes.
" The year can be set in the range of 2000 to 2099.
" The watchOs built-in full automatic calendar makes allowances for different monthSplit Time
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watchOs battery replaced.StartSplitSplit releaseStopClear
" The day of the week is displayed automatically in accordance with the date (year,( displayed)
month, and day) settings.Two Finishes
Daylight Saving Time (DST)StartSplitStopSplit releaseClear
Daylight Saving Time (summer time) advances the time setting by one hour from StandardFirst runner Second runner Display time of
Time. Remember that not all countries or even local areas use Daylight Saving Time.finishes.Display time of finishes.second runner.
first runner.
To toggle the Timekeeping Mode time between DST and Standard Time
1.In the Timekeeping Mode, hold down A until the
DST indicator seconds start to flash, which indicates the setting
screen.
2.Press C twice to display the DST setting screen.
3.Press D to toggle between Daylight Saving Time ( )
and Standard Time ( ).
4.Press A to exit the setting screen.
" The DST indicator is displayed on the Timekeeping
Mode and Alarm Mode screens while Daylight Saving
On/Off status Time is turned on.
1 |