Module No. 22862286-1
GENERAL GUIDE
?Press C to change from mode to mode.
?Pressing L in any mode illuminates the display for about 3 seconds.
?If you do not perform any operation for a few minutes while a setting screen (with flashing digits) is on the display, the watch automatically exits the setting screen.
?If you do not perform any operation for a few minutes in the Data Bank Mode or Day Counter Mode, the watch automatically reverts to the normal timekeeping screen.
Timekeeping ModeData Bank ModeDay Counter ModeAlarm ModeStopwatch ModeDual Time Mode
Press C.
TIMEKEEPING MODEDATA BANK MODE
?Press D to toggle between 12-hour and 24-hour timekeeping.The Data Bank Mode lets you store up to 25 records, each with a name (up to eight
characters) and a phone number (up to 12 digits). Data is automatically stored into
Day of weekalphabetical order based on the name data. You can recall records by scrolling
through them on the display.
DST on indicator Mode indicator
Year - Month - Day
Seconds
Remaining memory
PM indicatorMinutes
Text area
Hour
Number area
?With 12-hour timekeeping, times between midnight and noon are indicated by A
(am), while times between noon and midnight are indicated by P (pm).
?The A and P indicators do not appear when you are using 24-hour timekeeping.
To set the time and date
1.While in the Timekeeping Mode, hold down A until the?The record on the display when you exit the Data Bank Mode appears first the next
seconds digits flash on the display, indicating the
time you enter the Data Bank Mode.
setting screen.
To input a new Data Bank record
1.In the Data Bank Mode, use D or B until the new data
screen appears.
?If the new data screen does not appear when you
press D and B, it means that memory is full. To
store another record, you will first have to delete a
record stored in memory.
2.Press C to move the flashing in the sequence shown below.2.Hold down A and a cursor appears on the text area.
SecondsDSTHour
[ New Data Screen ]
DayMonthYearMinutes
3.Use D or B to scroll through characters at the current cursor position. Characters
3.While the seconds setting is selected (flashing), press D to reset it to 00. If youscroll in the sequence shown below.
press D while the seconds setting is in the range of 30 to 59, the seconds are
reset to 00 and 1 is added to the minutes. If the seconds setting is in the range ofPress .Press .
00 to 29, the minutes count is unchanged.
?While the DST* setting is selected (DST on indicator is flashing), press D to(Space)A to Z0 to 9
toggle it on (on) and off (OF). If DST setting is on, the DST on indicator is shown
in the Timekeeping Mode, Day Counter Mode and Alarm Mode.
?Holding down either button scrolls at high speed.
4.While any other setting is selected (flashing), press D to increase it or B to
4.When the character you want is at the current cursor position, press C to move the
decrease it. Holding down either button changes the setting at high speed.cursor to the right.
5.After you make the settings you want, press A to exit the setting screen.
?The day of the week is automatically set in accordance with the date.5.Repeat the steps 3 and 4 to input the rest of the characters.
?The date can be set within the range of January 1, 2000 to December 31, 2039.?You can input up to eight characters for the name, though only three characters
?The watchOs built-in full automatic calendar automatically makes allowances forare visible at a time. If the name you input has fewer than eight characters, use
different month lengths and leap years. Once you set the date, there should be noC to move the cursor to the eighth space (which means you would press C
reason to change it except after the replacement of the watchOs battery.three times after inputting a five-character name).
*Daylight Saving Time (DST), which is also sometimes called Osummer time�?Holding down C to move the cursor at high speed.
advances the time for one hour, as is the custom in some areas during the6.After you input the name, use C to move the cursor to the number area.
summer. Remember that not all countries or even local areas use Daylight Saving?Pressing C while the cursor is located at the eighth character of the text area
Time.advances to the number area. Pressing C while the cursor is located at the 12th
digit of the number area returns to the text area.
7.Use D or B to scroll through characters (hyphen, numbers, space) at the current
cursor position on the number area. Characters scroll in the sequence shown
below.
ABOUT THE BACKLIGHT
Press .Press .
Press L to illuminate the display for about 3 seconds.
?The backlight of this watch employs an electro-luminescent (EL) light, which loses0 to 9(Space)
its illuminating power after very long term use.
?Frequent use of the backlight shortens the battery life.?Holding down either button scrolls characters at high speed.
?The watch emits an audible sound whenever the display is illuminated. This does
?You can input up to 12 digits for the number.
not indicate malfunction of the watch.8.After inputting the name and number of the record, press A to store it and exit the
?The illumination provided by the backlight may be hard to see when viewed undersetting screen.
direct sunlight.
?The display can show only three name characters at a time. Longer names scrolls
?The backlight automatically turns off whenever an alarm sounds.continuously from right to left. The symbol O � indicates that the character to the
left is the last, and the character to the right is the first.
To recall Data Bank data
In the Data Bank Mode, press D to scroll forward through the stored data items or B
to scroll in reverse.
?Holding down either button scrolls at high speed.
To edit Data Bank data items
1.In the Data Bank Mode, use D or B to display the data you want to edit.
2.Hold down A until the cursor appears in the display.
3.Use C to move the cursor to the character you want to change.
?Holding down C to move the cursor at high speed.
4.Use D or B to change the character.
?Holding down either button scrolls characters at high speed.
?See step 3 of OTo input a new Data Bank record� for information on inputting
name characters, and step 7 for inputting number characters.
5.After making the changes that you want, press A to store them and exit the setting
screen. |
ACEC
