2177-2
TELEMEMO MODEEASY TIMER MODE
Mode indicatorThe Telememo Mode lets you store up to 10 records, eachMode indicatorThe Easy Timer Mode lets you quickly and easily set a
with a name (up to eight characters) and a phone numbercountdown timer within the range of 1 to 60 minutes. When
Page number(up to 12 digits). You can recall records by scrolling throughthe end of the countdown is reached, an alarm sounds for
them on the display.10 seconds, or until you press any button on the watch.
"The page number on the display when you exit the Tele-When the alarm stops, the countdown start time is cleared
memo Mode appears first the next time you enter theautomatically.
Telememo Mode.
Using the Easy Timer
To input a new Telememo record1.In the Easy Timer Mode, use D(+1 minute) and
1.In the Telememo Mode, press D(+) or B(�) to displayB(�1 minute) to change the start time setting. Holding
the page number of the record where you want to inputdown either button changes the start time at high speed.
data.2.Release the button, and the countdown starts automati-
2.Hold down A and a cursor appears on the text area.Minutescally in about one second.
Seconds"If you want to set the starting time to [ :60 00], press B
while [ :00 00] is on the display in the Easy Timer Mode.
3.Use D to scroll through characters at the current cursor position. Characters scroll"You can use D(+) and B(�) to change the start time setting while a countdown is
in the sequence shown below.in progress. The seconds count is unchanged by pressing B or D.
3.An alarm sounds for about 10 seconds when the end of the countdown is reached.
Press D."To stop a countdown, press A. This also resets the countdown time to [ :00 00].
(Space)A to Z0 to 9 . (Period) - (Hyphen)
"Holding down D scrolls at high speed.
4.When the character you want is at the current cursor position, press C to move
the cursor to the right.ALARM MODE
Press C.Hourly time signal on When the Daily Alarm is turned on, the alarm sounds for
1st digit8th digitText areaindicator20 seconds at the preset time each day. Press any button
Alarm on indicatorto stop the alarm after it starts to sound. When the Hourly
12th digit1st digitNumber areaTime Signal is turned on, the watch beeps every hour on
Mode indicatorthe hour.
"Holding down C to move the cursor at high speed.
5.Repeat the steps 3 and 4 to input the rest of the characters.To set the alarm time
"You can input up to eight characters for the name, though only three characters are
1.While in the Alarm Mode, hold down A until the hour
visible at a time. If the name you input has fewer than eight characters, use C todigits flash on the display, indicating the setting screen.
move the cursor to the eighth space (which means you would press C three times
"At this time, the alarm is turned on automatically.
after inputting a five-character name).
2.Press C to move the flashing in the sequence shown
6.After you input the name, use C to move the cursor to the number area.below.
"Pressing C while the cursor is located at the eighth character of the text area
advances to the number area. Pressing C while the cursor is located at the 12thHourMinutes
digit of the number area returns to the text area.HourMinutes
7.Use D to scroll through characters (hyphen, numbers, space) at the current cur-3.Use D to increase the setting. Holding down D
sor position on the number area. Characters scroll in the sequence shown below.DST on indicatorchanges the setting at high speed.
Press D.4.After you set the alarm time, press A to exit the setting screen.
- (Hyphen)0 to 9(Space)"The format (12-hour and 24-hour) of the alarm time matches the format you select
in the Timekeeping Mode.
"When setting the alarm time using the 12-hour format, take care to set the time
"Holding down D scrolls characters at high speed.correctly as morning or afternoon.
8.When the character you want is at the cursor position, press C to move the cursor
"If the DST on indicator is on the display, that indicate the DST on/off setting of the
to the right.
Timekeeping Mode is on.
9.Repeat steps 7 and 8 to input the rest of the numbers you want.
"You can input up to 12 digits for the number.
10. After inputting the name and number of the record, press A to store it and exitTo stop the alarm
the setting screen.Press any button to stop the alarm after it starts to sound.
"The display can show only three name characters at a time. Longer names scrolls
continuously from right to left. The symbol O � indicates that the character to the leftTo turn the Daily Alarm or the Hourly Time Signal on and off
is the last, and the character to the right is the first.Press B while in the Alarm Mode to change the status of the Daily Alarm and Hourly
"The number area can show up to six digits at one time. If a number has more thanTime Signal in the following sequence.
six digits, the display automatically switched between the first six digits (counting
forward from the first digit) and the last six digits (counting backward from the last
digit) of the number. This means that if a number is 12 digits long, the number area
switches between the first six digits and the last six digits. If a number is sevenBoth ONBoth OFFDaily AlarmHourly Time
digits long, the number area switches between digits 1 through 6, and digits 2 throughonlySignal only
7.
To recall Telememo dataTo test the alarm
In the Telememo Mode, press D(+) or B(�) to scroll forward through the storedIn the Alarm Mode, hold down D to sound the alarm.
records.
"Holding down either button scrolls at high speed.
To edit Telememo data items
1.In the Telememo Mode, use D(+) or B(�) to display the data you want to edit.
2.Hold down A until the cursor appears in the display.
3.Use C to move the cursor to the character you want to change.
4.Use D to change the character.
"See step 3 of OTo input a new Telememo record� for information on inputting name
characters, and step 7 for inputting number characters.
5.After making the changes that you want, press A to store them and exit the set-
ting screen.
To delete a Telememo record
1.In the Telememo Mode, use D(+) or B(�) to display the record you want to de-
lete.
2.Hold down A until the cursor appears in the display.
3.Press D and B at the same time. The message OCLR � appears in the display,
indicating that the record was deleted.
"After the record is deleted, the cursor appears in the text area, ready for input.
4.Input a new record or press A to exit the setting screen. |