Module No. 21652165-1
GENERAL GUIDE
?If the contents of the display seem to be continually changing, see OAUTO DISPLAY FUNCTION� for information on how to stop it.
?Press CCCCC to change from mode to mode.
?In any mode, press LLLLL to illuminate the display for about 3 seconds.
Timekeeping ModeTelememo ModeAlarm ModeStopwatch Mode
Day of TheTime Graph
Week DisplayDisplay
Press BBBBB.
TIMEKEEPING MODE5.After you set the time and date, press AAAAA to return to the Timekeeping Mode.
?The day of week is automatically set in accordance with the date.
Month - Day?In the Timekeeping Mode, press DDDDD to switch between?The date can be set within the range of January 1, 1995 to December 31, 2039.
Day of weekthe 12-hour and 24-hour formats.?If you do not operate any button for a few minutes while a selection is flashing, the
?Press LLLLL in the Timekeeping Mode to activate the ELflashing stops and the watch goes back to the Timekeeping Mode automatically.
backlight and to display animated graphics.
FRI?The Timekeeping Mode has two displays. One showsAbout the backlight
the Mark along with the current day of the week. TheIn any mode, press LLLLL to illuminate the display for about 3 seconds.
other display shows a time graph for the current date.
Pressing BBBBB switches between the two displays.?The backlight of the watch employs an electro-luminescent (EL) light, which loses
?There are three different time graph formats, whichilluminating power after very long use.
change automatically in accordance with the current re-?The illumination provided by the backlight may be hard to see when viewed under
lationship between an alarm time setting and the cur-direct sunlight.
rent time.?The watch will emit an audible sound whenever the display is illuminated. This is
HourSecondscaused by a transistor that vibrates when the EL panel lights up. It does not indi-
Minutescate malfunction of the watch.
?The backlight automatically turns off whenever an alarm sounds.
PM indicator
No Alarm Time Setting for Current Date
Month - Day
Time graphTELEMEMO MODE
Caution
The following causes all data stored in memory to be deleted. Be sure to
always keep separate written copies of all important data.
Malfunction or repairs/Dead battery/Battery replacement
In no event will CASIO be liable for loss of data or any damages arising out of
such loss.
Alarm Time Setting for Current Date
Appointment icon
An appointment icon appears on the display and the timeMode indicatorThe Telememo Mode lets you store up to
Time graphgraph hour for which the alarm is set flashes. The time20 pages of name, telephone number, and
graph shows how long before the alarm time will becell phone (or pager) number data. You can
Appointmentreached.recall data by scrolling through it on the dis-
time indicatorplay.
?The number of unused pages still availa-
Remainingble for storage of data appears on the dis-
memoryplay every time you enter the Telememo
Mode.
NameC?You can input up to eight characters in
the text area, and 12 digits in each of the
Telephonetwo (telephone and cell phone) number
numberareas.
?The data item on the display when you
exit the Telememo Mode appears first the
Month - Daynext time you enter the Telememo Mode.
Alarm Time Setting Within the Hour[New Data Display]To input new Telememo data
Appointment iconText area1.In the Telememo Mode, press DDDDD or BBBBB until the New
One hour before an alarm time is reached, a tone sounds
Time graphand the time graph format changes, replacing the monthdata display appears.
and day with a countdown of the minutes and seconds
?The new data display is the one that is blank (contains
Appointmentleft until the alarm time is reached.no name and telephone number).
time indicator
?If there is no Telememo data stored in memory yet, the
new data display appears as soon as you enter the Tele-
memo Mode.
?If the message O� appears on the display, it
means that memory is full. To store more data, you will
Number areafirst have to delete some of the data.
2.Hold down AAAAA and a cursor appears in the text area.
3.Use DDDDD or BBBBB to input a character at the cursor position. The character changes in
the following sequence. Holding down either button changes the character at high
speed.
Remaining minutes and secondsPress .
(Space)A to Z0 to 9
To set the time and datePress .
1.Hold down AAAAA while in the Timekeeping Mode. The seconds digits flash on the
display because they are selected.4.After you select the character you want, press CCCCC to advance the cursor to the right.
2.Press CCCCC to change the selection in the following sequence.?Repeat 3 and 4 until you complete name input.
?You can input up to 8 characters in the name area.
SecondsHourMinutesYear5.After the name input is through, use CCCCC to move the cursor to the telephone number
area.
6.While the cursor is in the telephone number area, use BBBBB or DDDDD to input a number
Animated GraphicDayMonthyou want. The character changes in the following sequence. Holding down either
button changes the character at high speed.
3.While the seconds digits are selected (flashing), press DDDDD to reset the seconds to
00. If you press DDDDD while the seconds count is in the range of 30 to 59, the secondsPress .
are reset to 00 and 1 is added to the minutes. If the seconds count is in the range� (Hyphen)0 to 9(Space)
of 00 to 29, the minutes count is unchanged.Press .
4.While any other digits (besides seconds) are selected (flashing), press DDDDD to in-7.After you select the character you want, press CCCCC to advance the cursor to the right.
crease the number or BBBBB to decrease it. Holding down either button changes the?Repeat 6 and 7 until you complete number input.
current selection at high speed.8.After you input the telephone number you want, use CCCCC to move the cursor to the
?While the animated graphic is flashing, you can select one of the following graph-cell phone number area.
ics. The animated graphic you select appears on the display whenever you turn on?The indicator indicates the cell phone display.
the EL backlight in the Timekeeping Mode.?Input the cell phone number using the same procedure as you did for the telephone
1.Random selection of 2, 3, or 4.number.
2.LOVERS A?If you donOt want to input a cell phone number, proceed from step 9 without input-
3.LOVERS Bting anything.
4.LOVERS C |
ACEC
